Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Ontario
Electric gate repair in Ontario, CA typically runs $180 – $640 depending on whether it’s a sensor adjustment, a hinge repair, or a full operator replacement, and most jobs are diagnosed within one visit. We work on the brand you already have, from Mighty Mule residential openers to DoorKing commercial operators, and we carry the parts that actually fail here: heat-stressed capacitors, wind-loosened hinge posts, and fried control boards. If your gate is stuck open, stuck shut, or grinding at 2 a.m., call (855) 942-4867 and you’ll talk to someone who knows Ontario’s gate stock, not a call center reading a script.
We’re in Ontario constantly. Riverside Gate Company runs routes through 91762, 91764, and the commercial corridors along the 10 and 60, so response time here isn’t theoretical. It’s a route we drive weekly.
Why Riverside Gate Company Is Ontario’s Preferred Electric Gate Repair Company
Most gate repair calls in Ontario come from one of two situations: a 1960s-era wrought iron gate whose hinges gave out, or a newer vinyl driveway gate that stopped responding to the remote. Both take different tools, different parts, and different diagnostic instincts. We carry both toolboxes, because Ontario’s housing stock demands it. The older neighborhoods near downtown have gates that were installed before automatic operators were common, retrofitted over the years with whatever controller was on sale. The newer HOAs east of Vineyard have exacting spec sheets. A general handyman won’t know the difference. We do.
Neil Dravecky built Riverside Gate Company around one idea: gate repair is its own trade. Electric motors, control boards, limit switches, safety loops, photovoltaic eyes. None of it is garage door work. None of it is fence work. It is gate work, and when a Mighty Mule operator in Ontario fries during a July heat wave, the diagnosis is usually a motor capacitor that’s been cooking for three summers, not a bad battery. Knowing that on the first visit saves you money.
Styles & brands we work with
Gate Access Control in Ontario
Gate Access Control in Ontario means more than fixing a keypad. It means programming intercom systems, keypads, telephone entry units, and vehicle detection loops so that the right people get in and everyone else stays out. In Ontario’s shared driveway situations, where two or three homes sit behind one gate, access control has to work every time, for every user, without one resident’s remote reprogramming wiping out another’s.
Keypad and Telephone Entry
Older Ontario homes often have hardwired keypads that are starting to show corrosion on the contacts. We replace the keypad, test the wiring run, and reprogram entry codes on site. For multi-tenant situations, telephone entry with directory dialing works better than a four-digit code everyone shares.
Vehicle Detection Loops
Commercial gate operators along Ontario’s freeway corridors use in-ground loop detectors to open on approach. Thermal expansion in the pavement from 100°F summers plus heavy truck traffic causes loops to shift and fail. We run new saw-cut loops and tune the sensitivity so the gate opens for cars, not for bicycles or debris.
Commercial Gate Operator in Ontario
A Commercial Gate Operator in Ontario is a different machine than a residential opener. It cycles more, gets hit harder, and gets sued if it fails. DoorKing, Elite, and FAAC operators run on Ontario’s industrial sites along the 10 and 60 corridors, and when they fail, the failure is usually mechanical first: a gearbox that’s been grinding, a chain that’s stretched, a limit switch that’s drifted. We set the clutch torque, replace the worn gear set, and verify UL 325 compliance on the safety devices before we leave.
Gate Motor Repair for Slide Gates
Tight Ontario lots and shared driveways mean slide gates outnumber swing gates in many areas. Slide operators need clean tracks, straight rails, and a motor that isn’t fighting debris. We clean the rail, inspect the drive chain for stretch, and set the operator’s friction clutch so it doesn’t burn out its own motor.
Control Board Diagnostics
When a commercial operator in Ontario stops responding, the control board is usually the first suspect and the most expensive guess. We bench-test boards with known-good motors before replacing them, so we’re not throwing a $600 part at a $40 relay. That diagnostic discipline matters on high-use gate systems.
Trusted Brands We Service in Ontario
We’re a gate-exclusive shop, and we work on the brand you have: Ghost Controls and Mighty Mule for residential swing and slide gates, DoorKing and Elite for commercial and industrial operators. We don’t tell you to rip out a working motor because it’s not the brand we’d install. We repair the component that failed. For Ontario customers, that means parts in the van instead of two-week backorders, because we stock what breaks here.
See the difference
Before
After
Before
After
Before
AfterCommon Electric Gate Repair Problems We See in Ontario Homes
- Heat-induced operator shutdowns. Ontario summers regularly push past 100°F, and slide gate motors on tight shared driveways run hot. If your gate quits mid-afternoon but works at night, the motor’s thermal overload is tripping, not the remote.
- Pintle hinge and hinge post failure in 91762-era gates. Original 1960s gates around downtown Ontario weren’t built for automation. Motors add torque those old hinges were never meant to take, and the posts work loose in the footing. Hinge post replacement is the fix more often than a new gate.
- Wind-induced misalignment from Santa Ana events. A wind event slams a swing gate against its stop, the post leans a degree, the latch no longer lines up, and the safety sensor starts tripping. We reset posts, rehang the gate, and recalibrate limits in one visit.
- Sagging vinyl gates on HOA-managed properties. Vinyl gates in east Ontario communities fade and sag with heat and UV. HOAs in 91761 and 91764 require exact color match replacement. We carry color samples and replace the panel, not just the hardware.
Pricing for Electric Gate Repair in Ontario, CA
A gate keypad replacement in Ontario runs $160 – $280 including programming. Safety sensor or photocell replacement runs $140 – $220 per eye. Gate motor repair on a residential operator runs $240 – $520 depending on whether it’s a capacitor, a limit switch assembly, or a full motor swap. Commercial operator repairs along the 10 and 60 run $380 – $900 for gearbox, chain, or control board work. Worn pintle hinge repair with post footing replacement on older Ontario gates runs $280 – $650, depending on how much concrete we’re chipping out. You get the price up front, agreed before we touch a tool.
Call (855) 942-4867 for a free estimate in Ontario. We quote the repair, not a range you’ll regret.
We Also Serve Cities Near Ontario
Our Electric Gate Repair routes cover the whole inland corridor. In addition to Electric Gate Repair in Ontario, we regularly service gate systems in Montclair, Upland, Chino, and San Antonio Heights. If your property sits on the border, call us. We’ll tell you if the drive time makes sense.
Serving Ontario, CA — Our Local Coverage Area
We’re based in the Ontario area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Ontario
The safety photocell is the first thing to check. In Ontario’s dry conditions, dust and spider webs build up on the lens, and the eye misreads the obstruction. Clean both lenses with a dry rag. If the gate still reverses, the safety loop or the force setting may have drifted. Call (855) 942-4867 and we’ll diagnose it over the phone, then fix it on site if needed.
Yes. In the 91762 neighborhoods we regularly replace pintle hinges, and on gates where 60 years of torque has worn the hinge post footing oval, we re-set the post in fresh concrete rather than welding on a band-aid. That’s the repair that keeps the gate square for another decade.
Santa Ana winds push slide gates against their end stops and shift the rail. The operator loses track of where the gate is, the limit switches trip, and the motor starts straining. We re-align the rail, reset the limits, and tighten the drive chain so the operator stops fighting the gate.
We carry HOA-approved color samples from the major vinyl gate manufacturers and match the existing color before we order the panel. For faded vinyl gates in the newer east Ontario communities, we match the original uncut sample or the least-faded section of the existing gate. The replacement blends in, and the HOA stays out of your mailbox.
Yes. We maintain and repair DoorKing, Elite, and Viking commercial operators on Ontario’s industrial and warehouse properties along the 10 and 60 corridors. Loop detectors, heavy-duty gearboxes, and truck-impact repairs are all in our rotation. Call (855) 942-4867 and ask for the commercial service line.
Written by Neil Dravecky, Owner at Riverside Gate Company, serving Ontario since we opened our first Inland Empire route.