Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Ontario
Gate repair in Ontario, CA usually costs $220 – $540 for common jobs like hinge replacement, gate realignment, or operator troubleshooting, and more involved commercial or weld-and-rust repair can run $700 – $1,400. We’re Riverside Gate Company, a gate-exclusive shop based in Riverside, and we run calls all across Ontario’s 91758, 91761, 91762, and 91764 ZIPs every week. If your gate is dragging on the concrete, stuck halfway open, or the operator just hums without moving, call us at (855) 942-4867 and we’ll get someone out to Ontario, diagnose the fault, and quote a price before any wrench turns.
Ontario splits into two gate worlds. The older downtown streets in 91762 still hold onto 1960s-era wrought-iron and chain-link gates with original pintle hinges worn oval. The east-side HOA communities in 91761 and 91764 run uniform vinyl and aluminum gates with architectural standards attached. A tech has to be fluent in both before quoting anything. We are. That’s the only way gate repair in Ontario works without surprises.
Why Riverside Gate Company Is Ontario’s Preferred Gate Repair Company
We service nine automated gate brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – and that breadth matters in Ontario because the housing stock spans so many eras. A 1970s iron gate off Euclid Avenue likely runs a completely different operator than a 2015 vinyl slide gate in a 91761 HOA. We work on the brand you have. That’s the point.
Our techs arrive in Ontario ready for both sides of the city. In 91762, that means a welder and the right stock to repair rust-thinned iron or re-seat a worn hinge post. In 91761 and 91764, it means HOA-approved color samples for vinyl and aluminum. The quote you get is the price you pay – we price the job before any work starts, so there’s no invoice bigger than the number you agreed to.
Neil Dravecky leads the company, and the standard hasn’t drifted since day one: diagnose the real fault, explain it plainly, fix it right. Ontario customers keep calling us back because we don’t shim a sagging gate and call it done. We find out why it sagged.
Styles & brands we work with
Commercial Gate Repair in Ontario
Commercial Gate Repair in Ontario means keeping security gates operational along the 10 and 60 freeway corridors, where industrial and distribution properties depend on slide gates, cantilever gates, and heavy barrier operators every shift. We handle those systems from the motor to the control board – Loop detectors, safety edges, photo eyes, and operator logic all fall under our core competency. A stuck commercial gate isn’t a nuisance. It’s a loading dock that can’t receive, a yard that can’t lock, a tenant who can’t leave at night. We understand the urgency and we’re insured and bonded for commercial sites across Ontario.
Operators and Access Controls
We repair FAAC, BFT, LiftMaster, DoorKing, and Viking commercial operators. When a barrier gate at a warehouse near the 60 won’t open or a slide gate starts reversing mid-cycle, the fault often isn’t the motor itself – it’s a misaligned safety loop or a control board that stopped reading inputs. Our techs trace the entire circuit before replacing parts, which saves Ontario property managers money over parts-swapping guesswork.
Welds, Rails, and Track Repairs
Heavy commercial gates in Ontario take a beating from truck traffic and wind. We re-weld fractured gate frames, straighten bent tracks, replace worn rollers, and re-anchor gate posts that shifting soil has loosened. A typical commercial track and weld repair runs $500 – $1,100 depending on the gate length and damage extent.
Iron Gate Repair in Ontario
Iron Gate Repair in Ontario centers on the older neighborhoods near downtown 91762, where original 1960s wrought-iron gates show their age in specific ways: oval-worn pintle hinges, rust-through at the bottom rail, and post footings that have loosened after sixty years of Inland Empire heat and wind. We repair these gates properly instead of patching around the problem. If the post has shifted, we re-set it. If the hinge pin is worn, we replace it or weld in new stock.
Hinge, Post, and Weld Repair
On a 1960s tract street off the downtown core in 91762, our crew opened a swing gate that had dropped and was dragging on the concrete. The panel was fine. The original pintle hinge had worn oval inside the hinge post, so we re-set the post footing and re-hung the gate rather than just shimming the sag. That’s the difference between a repair that lasts and one that fails again next summer.
Rust Treatment and Realignment
Ontario’s occasional winter rain plus years of sprinkler overspray rusts untreated steel fast. We cut out rust-damaged sections, weld in matching stock, grind it flush, and prime and paint to match the existing finish. Then we align the gate so it swings true and the operator – if there is one – stops straining against a gate that doesn’t sit square. Typical iron gate rust repair and realignment in Ontario runs $350 – $750.
Trusted Brands We Service in Ontario
We work on the brand you have. In Ontario, that’s often FAAC on commercial slide gates along the freeway corridors, BFT on villa and HOA entry systems, Linear on mid-range residential operators, and Viking on heavier commercial barrier arms. We carry repair parts stock for all nine brands we service, so when your LiftMaster operator needs a new control board or your Ghost Controls arm won’t trigger, we’re not waiting a week on a distributor. Same-day parts availability means most Ontario repairs finish in one visit.
Common Gate Repair Problems We See in Ontario Homes
- Vinyl and aluminum gates sagging after 100°F+ summers. Repeated inland heat softens vinyl panels and loosens the hinge hardware, so the gate drops and drags on the driveway. The real fault is often a hinge post that pulled loose from the stucco pillar, not the gate panel itself – fixing the post is what stops it from happening again.
- Santa Ana wind damage knocking safety systems out of alignment. When 50 mph gusts slam your gate against its stops, the hinges loosen and the photo eyes or loop detectors shift just enough that the gate won’t close, or reverses for no reason. We re-align the sensors and torque the hardware, then run the full entrapment-protection cycle to verify it’s safe.
- Oval-worn 1960s pintle hinges in downtown 91762. It’s a signature problem in Ontario’s original tract-home neighborhoods. The hinge pin grinds the post hole into an oval over decades, so the gate drags no matter how much you shim it. The fix is re-setting the post or welding in new hinge stock, not another shim.
- HOA color-match failures on east-side vinyl gates. In 91761 and 91764 communities, a mismatched replacement panel gets rejected at architectural review. We match the faded color and profile before ordering anything, then handle the operator and safety checks in the same visit so the HOA sees one clean, compliant repair.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Ontario, CA
Here’s what Ontario homeowners and property managers should expect. A hinge and post repair on a residential iron or vinyl swing gate runs $220 – $480. Gate realignment alone is usually $180 – $350. Automated gate operator troubleshooting and repair runs $260 – $540, depending on whether it’s a control board, motor, or sensor fault. Weld and rust repair on iron gates falls between $350 and $750. Full commercial gate and operator repair jobs run $700 – $1,400. Every quote is given upfront, before any work begins, and we don’t start until you approve the number. Call (855) 942-4867 for a free estimate – we’ll come to Ontario, assess the gate, and write a price.
If your gate sits in an HOA community, approval timing matters. We can send you the spec sheet and material details for your architectural committee while the repair is still being quoted, so you’re not paying to fix a gate the HOA will reject. Plan on HOA approval adding a few days to the sequence, not to the cost.
We Also Serve Cities Near Ontario
Our gate repair route covers the surrounding Inland Empire, so if you’re in Montclair, Upland, Chino, or San Antonio Heights, Gate Repair in Ontario expertise applies equally to you – and our full-service Gate Repair team handles everything from a residential swing gate to a commercial slide gate. We’re a dedicated gate company, not a handyman who tacks gates onto a list of other trades. If it swings, slides, or opens with a motor, we fix it.
Serving Ontario, CA — Our Local Coverage Area
We’re based in the Ontario area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Ontario
In most Ontario HOA communities, especially on the east side in 91761 and 91764, yes – exterior gate changes require architectural committee approval, and that includes replacement panels, color changes, or style changes. A straight mechanical repair like a hinge replacement or operator fix on your existing gate typically doesn’t need approval, but a full gate replacement always does. We can provide spec sheets, material details, and color samples to your committee, and our techs are comfortable working to HOA architectural standards. Call (855) 942-4867 and we’ll help you sort out what your specific association requires before you spend money.
In Ontario, the hinge post is the culprit more often than people expect. When a 1960s pintle hinge wears oval inside the post, or a stucco pillar post loosens from decades of thermal expansion and Santa Ana wind, the gate drops no matter how sound the panel is. We diagnose by checking the post for movement and the hinge for wear before recommending a repair. If the post is loose, shimming the gate only postpones the real fix. Call us at (855) 942-4867 for an on-site assessment.
Yes. Any automatic gate operator in Ontario, California must have functioning entrapment protection – photo eyes, safety edges, or both – to comply with UL 325 standards and state safety codes. If your gate doesn’t reverse when it hits an obstruction or stays open when the beam is broken, the operator is unsafe and needs repair. We verify entrapment protection on every automatic gate repair we do, because a gate that closes on a child, a pet, or a car is not a working gate.
Yes, and this is exactly the split Ontario throws at you. In the older 91762 neighborhoods near downtown, we’re re-setting original 1960s pintle hinges, welding rust patches into iron, and realigning gates that have hung for half a century. In the east-side 91761 and 91764 HOA communities, we’re matching faded vinyl colors, replacing aluminum panels to spec, and verifying LiftMaster or BFT operators work with the community’s entry system. It’s the combination of old iron and modern vinyl that makes Ontario’s gate repair work different from anywhere else, and we handle both every week. Call (855) 942-4867 and tell us what kind of gate you have.
Yes. We regularly service commercial slide gates, cantilever gates, and barrier operators at Ontario industrial properties and distribution centers along the 10 and 60 freeway corridors. These jobs usually involve FAAC, BFT, DoorKing, or Viking operators, and often the fault is in the loop detector, the safety edge, or the control board rather than the motor itself. Our commercial repair work in Ontario typically runs $700 – $1,400 depending on scope, quoted before we start. Call (855) 942-4867 and we’ll schedule a site visit.
Call Riverside Gate Company for Gate Repair in Ontario
If your gate is stuck, sagging, rusting through, or failing HOA review, call us at (855) 942-4867. We’re a gate-exclusive company with parts for nine automation brands on hand, techs who can weld iron or match vinyl to spec, and the local knowledge to know which problem you’re likely facing before we even arrive. Free estimates, upfront pricing, and the quote is agreed before any work starts. From the motor to the control board, from downtown 91762 to the east-side HOAs, Riverside Gate Company fixes gates in Ontario.
Written by Neil Dravecky, Owner at Riverside Gate Company, serving Ontario, CA and the wider Inland Empire.