Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across La Verne
An electric gate that won’t open or close in La Verne usually comes down to one of three things: a control board that’s cooked, a motor that’s worn out, or a hinge and post problem that’s been building for years. We fix all three. Riverside Gate Company is a dedicated gate specialist serving La Verne, and we’re set up to diagnose and repair automatic gate systems from the motor to the control board without sending you to a general contractor first. Most La Verne repair calls are scheduled within one to two business days, and if a gate is stuck open or won’t secure, call (855) 942-4867 and we’ll talk through what’s happening and get someone out fast.
Key Takeaways
- La Verne electric gate repair typically runs $180 to $1,400 depending on whether it’s a control board, motor, or mechanical failure.
- We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
- Old Town historic gates often need retrofitting, not replacing, to keep the period iron or wood intact.
- Free estimates by phone at (855) 942-4867, with the exact price quoted before any work begins.
Why Riverside Gate Company Is La Verne’s Preferred Electric Gate Repair Company
La Verne’s gate inventory is not like neighboring cities. You’ve got century-old wrought iron in the citrus-era neighborhoods around Old Town and the University of La Verne, and then vinyl and wood driveway gates in the 1980s and 1990s tracts on the east side and up into the foothills. Each fails differently. We work on the brand you have, and we’ve been inside enough La Verne properties to know which operators show up on which streets. Neil Dravecky, who leads the company, built this business around gate automation specifically, so when we pull up to a home off Bonita Avenue or a commercial property near Foothill Boulevard, we’re not learning on your gate. We’ve already seen that model and that failure mode dozens of times.
We don’t ask you to explain the difference between a swing arm and a slide operator. We ask you what the gate is doing and what it sounds like. From there we know what’s likely wrong before the truck rolls. La Verne customers call us because the gate is the only thing between the street and their property, and they don’t want a fence company apprentice guessing at a control board. That’s fair, because control boards and loop detectors don’t guess, and neither do we.
Styles & brands we work with
Electric Gate Motor in La Verne
Electric gate motor repair in La Verne means diagnosing whether the motor itself has failed, or whether the motor is being forced to work against a gate that can’t move. That distinction matters. In La Verne’s expansive clay soil, winter rains heave the gate posts, the gate goes out of level, and a perfectly healthy motor burns itself out trying to drag a panel that no longer clears the ground. So the first thing we check is whether the motor is still serviceable and whether the mechanical side, hinges and posts and alignment, is what killed it.
Most electric gate motor repairs in La Verne run between $275 and $700 depending on the operator brand and whether we’re swapping the motor unit, the capacitor, or the gear assembly. Full motor replacement on a slide gate runs $900 to $1,400 on average, including the re-set of limits and safety check.
Motor replacement vs. repair
If the motor has simply worn out and the operator chassis is still solid, we replace the motor and keep your existing control board and receiver, which keeps the cost down. If the gear train is scored and the capacitor is swollen, replacement is the honest call, and we’ll tell you that before you commit. We don’t rebuild a motor that’s cheaper to replace, and we don’t replace an operator that only needed a $180 capacitor.
Same-day assessment for stuck gates
When a gate motor in La Verne dies with the gate open, that’s a security problem, not a convenience problem. The panel sits open all night. We prioritize those calls and will get someone out to at least disengage the operator and manually secure the gate, then give you a repair quote on the spot. Call (855) 942-4867 and tell us the gate is stuck open, and we’ll route it accordingly.
Gate Access Control in La Verne
Gate access control in La Verne covers the keypad, the remote receiver, the loop detector in the driveway, and the phone or intercom system that tells the gate to open. When any of those fails, the gate itself is fine but no one can get in, and that’s often worse from a resident’s point of view. We see this constantly in the foothill tracts where driveway gates run multiple times a day and keypads get hit with direct afternoon sun for years. The UV here is intense, and it cracks keypad membranes and fades the button labels until someone’s stabbing at a blank pad at 10 p.m.
Keypad replacement in La Verne runs $150 to $350 installed, remote transmitters $45 to $85 each programmed, and a new loop detector install runs $400 to $650 including cutting the loop in the concrete or asphalt. We quote the exact price before starting, so you’re not getting a surprise on the back end.
Keypad and remote programming
We work with the access control brand already on your gate, so we’re not trying to sell you a whole new keypad because we don’t carry your brand. Adding a keypad or reprogramming remotes on an existing LiftMaster, DoorKing, or Viking system is routine for us. If a homeowner in La Verne bought a used remote online that won’t sync, we can usually get it paired in one visit.
Loop detectors and vehicle sensors
Loop detector failures show up as a gate that opens for one car and not the next, or a gate that starts to close on a car halfway through. With La Verne’s clay soil, loop wires can also shear as the ground moves over years. We locate the break, splice or pull new wire, and retune the detector to the proper sensitivity for the driveway length.
Trusted Brands We Service in La Verne
We work on nine gate automation brands, which covers nearly every operator installed in La Verne. That includes the professional-grade commercial units on Foothill Boulevard properties, like BFT and Viking, plus the residential systems common on single-family homes, like Linear and Ghost Controls. The useful part for La Verne homeowners is that we stock common boards, remotes, safety edges, and hinge hardware on the trucks, so most repairs don’t wait on a special order. If the board on your swing gate is dead, we’re not going to tell you it’s obsolete and you’re out of luck. We’ll either source it, cross-reference it, or retrofit a current operator behind your existing gate panel. Repair or replace, we handle both.
Common Electric Gate Repair Problems We See in La Verne Homes
- Dead control boards on legacy operators: Pre-1990s operators still run in Old Town and near the University of La Verne. Their boards fry during long hot spells when the capacitor ages out, and most of those boards have no direct replacement anymore. We retrofit modern boards or swap the operator while keeping the original gate panel.
- Seized hinge pins on wrought-iron gates: The pattern repeats block after block in La Verne’s older neighborhoods. The first heat wave of summer dries the last of the old grease, the pin rusts solid, and the swing gate binds and stalls the motor. We swap the pin, correct the sag, and re-lube for the La Verne climate before putting the operator back under load.
- Sun-rotted vinyl gates on the east side: Vinyl privacy gates in the east-side tracts and foothill areas take intense afternoon UV, and after 15 to 20 years the material gets brittle and cracks at the hinge blocks. The operator is usually fine, but the panel no longer rides level. We repair the frame or remount the gate and readjust the travel limits for the new geometry.
- Clay soil heaving posts and footings: After a wet La Verne winter, the expansive clay swells and shifts. Driveway gate posts lean just enough to throw the gate out of square. That misalignment strains the operator until it short-cycles or trips the obstruction sensor. We correct the post alignment and recalibrate the operator so it’s not fighting the ground.
See the difference
Before
After
Before
After
Before
AfterPricing for Electric Gate Repair in La Verne, CA
La Verne pricing for electric gate work runs a real range, and it depends mostly on whether the failure is electrical or mechanical. A straight control board swap runs $350 to $650 including the part, a keypad or photo eye $150 to $350, and a motor replacement $275 to $700 on most residential swing gates. Slide gate motor jobs run higher because of the gearbox, usually $900 to $1,400. A hinge pin replacement with sag correction is typically $180 to $350, and a full post re-set in clay soil starts around $500 and goes up from there depending on the footing.
Every estimate is free. We tell you the price before the first tool comes off the truck, and that price is what you pay. No open-ended labor, no add-ons you didn’t approve. Call (855) 942-4867, tell us what the gate is doing, and we’ll give you a real range on the spot and book the visit.
| Repair in La Verne | Typical Price Range |
|---|---|
| Control board replacement | $350 – $650 |
| Motor replacement (swing gate) | $275 – $700 |
| Motor replacement (slide gate) | $900 – $1,400 |
| Keypad replacement | $150 – $350 |
| Loop detector install | $400 – $650 |
| Hinge pin replacement / sag correction | $180 – $350 |
We Also Serve Cities Near La Verne
Our Electric Gate Repair team works throughout La Verne and the surrounding foothill and valley cities. We regularly take calls from Claremont, Pomona, Montclair, and Upland, and we’re familiar with the gate systems and soil conditions in each. If you’re in La Verne or just over the city line, the same crew covers it.
Serving La Verne, CA — Our Local Coverage Area
We’re based in the La Verne area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in La Verne
You can almost always keep the gate itself, especially in Old Town where the iron or wood panel is the character. We retrofit a current operator and control board behind the original gate, keeping the street-facing panel untouched. In the rare case where the gate panel is so degraded that no amount of repair will make it safe or reliable, we’ll show you exactly why and give you the replacement number alongside the repair number so you can make a real call. Call (855) 942-4867 for a free assessment, and we’ll tell you which route applies to yours.
UL 325 compliant entrapment protection means the gate reverses or stops when it contacts an obstruction, and it requires either monitored safety edges or a photo eye system depending on the installation and operator vintage. Many of the legacy gates we see in La Verne, especially the pre-1990s operators, have no functioning entrapment protection at all. That’s a genuine safety issue. We check this on every repair visit and can retrofit photo eyes onto an existing gate and operator without replacing the panel.
It’s the hinge pins, not the operator. In La Verne’s dry heat, whatever grease was on the pin last winter bakes out, the pin rusts against the barrel, and the gate starts dragging on the sidewalk or the driveway. The motor then works harder until it trips or stalls. We replace the seized pin, correct the sag at the post, and use a lubricant that holds up through a La Verne summer. The operator usually returns to normal once the panel moves freely again.
We service nine gate automation brands, including BFT, Linear, Viking, and Ghost Controls, so the answer is almost always yes. We stock common boards, remotes, and safety components for those brands on our trucks. If your operator is from a brand outside our list, we’ll tell you straight and either source the part or recommend a retrofit that fits behind your existing gate.
Yes. Foothill tract driveway gates in La Verne run multiple cycles a day and the keypads and loop detectors take the beating. We replace keypads, reprogram remotes, repair broken driveway loops, and retune detector sensitivity for the specific driveway length and metal content in the concrete. These fixes usually take one visit. Call (855) 942-4867 for an exact quote.
Old Gates, New Electronics: Why La Verne Is Different
La Verne’s Old Town historic district has design guidelines that most handyman gate services never think about. When a street-facing wrought-iron pedestrian gate or an original wood driveway gate fails, you often cannot just pull it out and drop in a modern aluminum unit. The historic character of the front elevation has to stay. So the real work becomes retrofitting modern operators, new control boards, and updated safety devices behind period-appropriate panels. That’s a different job, and it’s one we’ve done enough times to have it down. An Old Town property off D Street called us because its wrought-iron pedestrian gate had stopped working after a Santa Ana wind event. The original operator board had fried, and the rusted hinge pin on the post had seized so badly the gate was dragging on the sidewalk. We replaced the obsolete control board, swapped the seized hinge pin, did a sag correction at the post, and added a working safety photocell before putting the gate back into service under its original iron. The gate still looks like it’s been there since the citrus era. It just opens and closes like a new one.
That’s the honest read on La Verne gate work. A legacy operator on an old iron gate can often be retrofitted for less than a full replacement, but there’s a line where the old board, the old hinge, and the old post all need to be done and the cost catches up to new. We’ll tell you when you’re under that line and when you’ve crossed it. No guessing, no upselling, just the gate working when we leave.
Call (855) 942-4867 for a free estimate on electric gate repair in La Verne. We’ll quote the price before the work starts, and the price we quote is the price you pay.
Written by Neil Dravecky, Owner at Riverside Gate Company, serving La Verne and the surrounding cities with dedicated gate repair and installation.