Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Bloomington
Electric gate repair in Bloomington usually means one of three problems: the operator stalled, the gate came off-line, or the safety system stopped working. Most jobs we handle here run between $185 and $420 parts included, and we can usually get a technician out to Bloomington the same day you call. Riverside Gate Company works on the brand you have, from the motor to the control board, and we quote the full price before any work starts. If your gate is down, stuck, or refusing to close, call us at (855) 942-4867 and we’ll get it moving again.
Bloomington is different from the cities around it. The lots are bigger, the driveways are longer, and a lot of the gates out here started life on farm and ranch entrances rather than residential driveways. That means we’re not just chasing burned-out keypads. We’re pulling grit out of slide-gate tracks, re-filling battery banks on solar operators, and re-squaring gates that have sagged off their hinge posts after twenty summers in the heat.
Why Riverside Gate Company Is Bloomington’s Preferred Electric Gate Repair Company
We’re a gate-exclusive specialist. That matters in Bloomington because the mix of properties here, from 1950s-era homes near Valley Boulevard to larger acreage parcels further out, means the gate at one house might be a light Mighty Mule swing arm and the next one down the road a heavy commercial-grade slide operator. Most general repair services either decline the commercial board work or misdiagnose the residential issue and start replacing parts that didn’t need replacing.
Our technicians work on nine automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That range is the point. A homeowner with a Ghost Controls opener on a solar panel and a property manager with a FAAC operator on a warehouse gate are both in our wheelhouse, and both get the same response time to Bloomington. Neil Dravecky runs the company, and the standard he holds the crew to is simple: diagnose before you quote, quote before you touch, and don’t leave until the gate cycles twice under its own power.
Because we’re not a general contractor, we’re not going to walk your property and pitch you a fence replacement or a garage door tune-up. Gates are what we do. That focus is why Bloomington customers call us when the gate has been down for a week and two other companies have already looked at it.
Styles & brands we work with
Gate Opener Repair in Bloomington
Gate opener repair in Bloomington usually comes down to the operator being asked to move more weight than it was rated for, or being asked to move a gate that no longer rolls or swings square. Wide driveways, trailers, and work trucks mean a lot of the gates out here are built heavy, and when a slide gate picks up a bind from a gritty track, the opener stalls and the homeowner assumes the motor is shot. Half the time the opener is fine, and the repair is in the track, the rollers, or the gate geometry. A typical gate opener repair in Bloomington runs $190 to $390 depending on whether we’re replacing a motor, a limit switch, or a full control board.
Motor and Limit Switch Diagnosis
A stalled slide gate on a long Bloomington driveway is often a limit-switch problem rather than a dead motor. The opener thinks the gate has traveled further than it has, cuts power, and leaves the gate half-open. We test the motor under load before quoting a replacement, and if the motor is fine, we won’t sell you one.
Solar Opener Battery and Charge Issues
On Bloomington properties where mains power doesn’t reach the gate, the opener runs off a solar panel and a battery bank. Hot, dusty months out here are hard on those systems. The panel gets coated, the battery loses capacity, and the gate quits mid-cycle or won’t hold a full open. Repair often means cleaning and re-aiming the panel, load-testing the battery, and sometimes upgrading to a larger panel or a second battery so the gate runs through the whole season instead of dying by August.
Automatic Gate Repair in Bloomington
Automatic gate repair in Bloomington goes beyond the opener, and this is where the county angle comes in. A lot of large-lot gates out here were installed years ago without a permit, which means no one ever verified the entrapment protection. When we repair an automatic gate in Bloomington, we check the full electrical and safety picture: motor, control board, safety photocells, edge sensors, and the UL 325 compliance items. Typical automatic gate repair in Bloomington runs $210 to $460, with safety-sensor replacement on the lower end and control-board replacement on the upper end.
Safety Photocell and Edge Sensor Replacement
A gate that reverses without touching anything, or won’t close at all, usually has a dead photocell or a failed safety edge. The board sees an obstruction that isn’t there and refuses to close. On older Bloomington gates, it’s common to find the photo-eyes missing entirely, and part of the repair is bringing the gate up to current entrapment-protection standards while we’re there.
Control Board and Receiver Work
When an automatic gate won’t respond to any remote, keypad, or hard-wired input, the problem lives in the control board or the receiver. We bench-test boards before condemning them because a failed receiver module looks identical to a failed board, and replacing the wrong one is an expensive mistake. On FAAC and Viking boards we keep common replacement components on hand, which shortens the wait for Bloomington customers.
Trusted Brands We Service in Bloomington
We work on the brand you have. If your Bloomington gate runs on FAAC, BFT, Linear, or Viking, our technicians know those systems down to the board level. We stock common parts and remote transmitters for those brands so a repair isn’t waiting on a week-long shipment, and when a part is obscure, we source it through our supplier network without marking it up twice. The point of carrying nine brands is simple: you shouldn’t have to call a different company for a Viking slide operator than you would for a Ghost Controls swing arm. Riverside Gate Company handles both.
See the difference
Before
After
Before
After
Before
AfterCommon Electric Gate Repair Problems We See in Bloomington Homes
- Wide slide gates packing grit into the rack and pinion. The open land around Bloomington kicks up fine dust that settles into the gear teeth and throws the gate out of alignment until the operator strains against the bind. We clear the rack, re-lube it, and re-square the gate so the motor isn’t fighting its own track.
- Solar operators stalling in the late summer. Long rural driveways without mains power rely on solar, and by August the panel is dusty and the battery is tired. The gate runs slow, stalls halfway, or won’t complete a cycle. We service the whole solar chain, not just the opener.
- Swing gates sagging off wooden hinge posts. In the older Bloomington tract areas near Valley Boulevard, decades of heat and dry air have split the posts the hinges are mounted into. Tightening the hinges doesn’t help; the post has lost its grip. The real repair is resetting the post in concrete and re-hanging the gate plumb.
- Gates with no working entrapment protection. Because many Bloomington operators were installed without a permit, safety photocells and contact edges were never added or checked. A repaired gate that still lacks UL 325 protection is a liability, so we include that verification on every automatic gate repair.
Pricing for Electric Gate Repair in Bloomington, CA
Here are the ranges we quote for Bloomington jobs, parts and labor included. Gate opener motor replacement runs $190 to $340. Control board replacement runs $260 to $460 depending on the brand. Safety photocell or edge sensor replacement runs $120 to $220. Solar battery and panel service runs $140 to $310. Slide-gate track and rack work runs $180 to $390. A service call to diagnose runs $89, and we credit that amount toward the repair if you proceed the same day. Every quote is written, itemized, and agreed before we start. Call (855) 942-4867 and we’ll give you a firm price over the phone for most common failures.
We Also Serve Cities Near Bloomington
Our Electric Gate Repair service area extends beyond Bloomington into Fontana, Rialto, Glen Avon, and Pedley, so if your property is near the city line, don’t assume we won’t come. We dispatch from Riverside and know the unincorporated pockets and county roads around Bloomington as well as the main streets. Call (855) 942-4867 and the dispatcher will confirm coverage for your address while you’re on the phone.
Serving Bloomington, CA — Our Local Coverage Area
We’re based in the Bloomington area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Bloomington
The operator is only responsible for moving the gate, so when a wide slide gate stalls partway, we test the gate’s own movement first. A gate that binds on a gritty track or a worn roller will stall any operator, and replacing the motor doesn’t fix the bind. In Bloomington, where dust off the open land packs into slide-gate racks, we see this weekly. The repair is usually cleaning and re-lubing the rack, replacing worn rollers, and re-squaring the gate off its post. If the motor then runs clean, you don’t need a motor. Call (855) 942-4867 and we’ll test it under load before quoting anything.
Yes, and we do it often. Long driveways here often can’t get mains power to the gate without a trenching job nobody wants, so the gate runs on solar. The typical failure is a battery that has lost capacity in the heat, a panel caked with dust, or a solar charge controller that has failed and stopped charging altogether. We test the panel output, the battery under load, and the controller before deciding what needs replacing. Sometimes it’s a $140 battery; sometimes the whole solar arrangement needs an upgrade to handle a heavier gate. Either way, we quote it before we touch it.
Repairs that replace existing components like operators, sensors, or boards do not require a permit through San Bernardino County. A new gate installation on a new footing can require a county permit, which Riverside Gate Company can pull as part of the project. The bigger issue in practice is that many older Bloomington gates were installed without anyone verifying entrapment protection, so on a repair we check and bring the safety items into compliance while we’re there. You won’t get a surprise invoice for it; it’s part of the written quote.
The sag usually isn’t in the hinges. On older Bloomington properties, especially around the tract areas off Valley Boulevard, the gate was hung on a wooden post that has dried and split over decades of heat and Santa Ana winds. Tightening the hinge bolts just pulls the hardware deeper into a post that has lost its structural grip. The fix is to reset the post in concrete, let it cure, and re-hang the gate plumb. Then the hinges hold because the post holds. We’ve done this on enough Bloomington lots to tell you within a few minutes of looking whether the post is salvageable or needs replacing.
Your gate has working entrapment protection if it reverses when the photocell beam is blocked and stops or reverses when the contact edge on the gate touches pressure. The test is simple: block the photo-eye with your hand and try to close the gate. If the gate closes anyway, the protection is failed or absent. On gates installed without a permit, the photo-eyes may never have been installed. Riverside Gate Company verifies UL 325 entrapment protection on every automatic gate repair in Bloomington, and we add the missing components when they’re not there.
If your gate is down, stalled, or running unsafely, call us at (855) 942-4867. We’ll diagnose it, quote it, and fix it. Estimates are free, and you’ll know the full price before we start the work.
Written by Neil Dravecky, Owner at Riverside Gate Company, serving Bloomington and the surrounding county since the company’s founding.