Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Crestline
Gate repair in Crestline usually means dealing with what the mountain does to a gate. At 4,500 feet in the San Bernardino Mountains, frost heave shifts gate posts, snow drags swing arcs out of alignment, and dry summer heat warps older wood panels. Riverside Gate Company handles all of it: mechanical hinge and post work, electric operator repair, control board replacement, and full gate realignment. Call (855) 942-4867 for a free estimate, and we’ll send a gate specialist, not a generalist.
We work on the brands Crestline homeowners actually have, from older LiftMaster and Linear operators on decades-old driveway gates to FAAC and BFT commercial systems on HOA entrances. If your gate drags, binds, won’t close, or has stopped responding to the remote, we diagnose the real cause, often a heaved post or a dead control board, and we fix it from the motor to the control board. If you’re in Crestline or nearby, we’re already familiar with how mountain weather stresses gate hardware.
Why Riverside Gate Company Is Crestline’s Preferred Gate Repair Company
We’re a gate-exclusive shop. That matters in Crestline, where the gate on a hillside cabin or a long gravel approach off Highway 138 sees conditions a flat-lot gate never faces. General repair services routinely decline electric gate work or misdiagnose the problem because they don’t carry gate automation parts. Our technicians work on gates every day, and they know the failure patterns specific to mountain properties: heaved post footings on graded lots, snow-drag bending swing arms, obsolete control boards in legacy operators, and fire-defensible rebuilds that need gates reset to current standards.
Neil Dravecky leads the team, and he’s built Riverside Gate Company around one focus: gate repair, electric gate troubleshooting, and gate installation. No fence work, no garage doors, no “we also do gates” sideline. That focus means we bring the right parts, the right test equipment, and the right diagnosis on the first trip. Our Gate Repair team stocks parts for the brands we service, so a Crestline callback doesn’t turn into a two-week wait for a control board.
- Gate-only focus: every job is within our core competency, so no one is learning on your dime.
- Nine automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We work on the brand you have.
- Mechanical and electrical depth: hinge and post repair, gate realignment, weld and rust repair, plus motor and control board work on automatic systems.
- State-licensed and insured: we are qualified to handle both the mechanical and low-voltage electrical sides of gate repair.
Styles & brands we work with
Wood Gate Repair in Crestline
Wood Gate Repair in Crestline is as much about the mountain climate as it is about carpentry. Older wood driveway gates here, many built in the 1940s through 1970s on cabin properties, shrink in dry summer heat and swell during wet winter storms. That seasonal movement loosens hinges, splinters stiles, and pulls the gate out of square against the latch post. It’s why wood gates in Crestline often need attention twice a year rather than once.
A typical wood gate repair in Crestline runs $180 to $450, depending on whether we’re replacing hinges, straightening a sagged frame, splicing a rotted bottom rail, or resetting a post. If the gate is dragging on plowed slush in January, the problem is usually frost heave under the hinge post, not the hinge itself. We fix the cause, not just the symptom.
Hinge and Post Work on Wood Gates
On graded hillside lots off Lake Gregory Drive or along the roads above Valley of Enchantment, hinge posts heave as the ground freezes and thaws. The gate drops, the latch misses, and the swing arc scrapes snow. We reset the post footing at the correct depth, re-hang the gate, and often install adjustable hinges so the gate can be re-leveled seasonally without major rework.
Warp and Rot Repair
Dry summer heat shrinks and warps wood panels, especially on south-facing gates that take full afternoon sun. We repair or replace split rails, reinforce sagging frames with steel strap, and treat or replace rotted bottom sections before the damage spreads to the hinge stiles.
Driveway Gate Repair in Crestline
Driveway Gate Repair in Crestline covers both the mechanical gate itself and the automatic operator that moves it. Many Crestline driveways climb steep, sloped approaches with dirt or gravel surfaces, and the gate at the bottom or top of that approach catches snow, slush, and runoff. That means operators work harder than they would on a flat lot, and the hardware degrades faster.
Expect to pay $220 to $600 for most driveway gate repairs in Crestline, including realignment, hinge replacement, operator arm repair, or limit switch adjustment. Larger jobs, like resetting a heaved post and re-hanging a heavy ornamental iron gate, run $600 to $1,200. The price is always quoted and agreed before any work starts, so there’s no surprise invoice at the end.
Electric Operator Repair
When an automatic driveway gate stops mid-travel, fails to close, or reverses for no reason, the cause is usually the operator: a worn limit switch, a failing capacitor, a stripped gear, or a control board that has lost its settings. We diagnose the specific fault, not just replace parts. We repair electric gate systems from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
Post Reset and Gate Realignment
A gate that scrapes the ground or won’t latch is usually not a hinge problem. In Crestline, the hinge post has often heaved or settled as the ground cycles. We reset the post in a proper concrete footing, correct the sag, and realign the gate and operator so the whole system works as one unit again.
Trusted Brands We Service in Crestline
Riverside Gate Company services gate automation from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common control boards, limit switches, remote transmitters, and safety photocells for these brands, so when we diagnose a failed FAAC board or a dead Mighty Mule arm on a Crestline gate, we can usually complete the repair on the same visit. We don’t sell you a brand we’re guessing at. We work on the brand you have, and we know the failure points of each one.
Common Gate Repair Problems We See in Crestline Homes
- Heaved hinge posts from frost and freeze-thaw cycles. Most January gate drags in Crestline trace back to a post footing that moved with the ground, not a worn hinge. We reset and re-anchor the post rather than lubricating hardware that was never the problem.
- Obsolete control boards in legacy operators. Older LiftMaster, FAAC, and Linear units from the 1990s and early 2000s often have boards with no serviceable replacement parts and no entrapment protection. When a retrofit board is unavailable, replacement is the cheaper answer, and we tell you that honestly.
- Snow and slush drag bending swing arms. Plowed snowbanks catch gate bottoms and bend operator arms, knock photocells out of alignment, and pull gates off their swing arcs. We fix the damage and often remount sensors above the typical drift line.
- Seasonal wood movement warping older gates. That same gate that dragged in January will shrink and cup in August. Wood gates in Crestline benefit from twice-yearly adjustment and realignment to keep latches working and operators from straining.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Crestline, CA
Here are honest ranges for Crestline gate repair work, based on what we typically see in the 92325 area. Hinge and latch repair on a standard wood or iron gate runs $140 to $320. Electric gate troubleshooting and operator repair runs $220 to $600. Full gate realignment after post heave runs $280 to $600. Post reset with new concrete footing runs $400 to $950. Control board replacement runs $300 to $800, depending on brand and board availability. A complete new residential automatic gate system install generally runs $2,800 to $8,500, depending on gate size, material, operator type, and driveway conditions. We provide a free estimate, and every price is quoted and agreed before any work starts. Call (855) 942-4867 to schedule.
We Also Serve Cities Near Crestline
Riverside Gate Company provides Gate Repair in Crestline and the surrounding mountain and valley communities, including Lake Arrowhead, Muscoy, San Bernardino, and Highland. If your property sits just outside Crestline or you manage gates at multiple locations across the San Bernardino range, we can usually route a technician to you quickly. Call (855) 942-4867 to confirm current response times.
Serving Crestline, CA — Our Local Coverage Area
We’re based in the Crestline area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Crestline
Usually not. In Crestline, a gate that drags in January is most often the result of frost heave under the hinge post. The ground freezes and swells, pushing the post up and dropping the gate. If the hardware was tight before the cold season, the hinge isn’t the problem, the footing is. We reset the post at the correct depth and re-hang the gate so it swings clean. Call (855) 942-4867 if yours is dragging now.
It depends on the operator and the board. Some older LiftMaster and FAAC units accept updated control boards with current UL 325 entrapment protection, and retrofitting those is honest and cost-effective. But many legacy boards from the 1990s and early 2000s have no serviceable replacement available. When parts are gone and safety features are missing, replacement is the cheaper answer over the next few winters. We’ll tell you which situation you have, straight, and quote both options before any work starts.
UL 325 is the safety standard that governs automatic gate operators, requiring entrapment protection like photocells, contact edges, or inherent obstruction sensing. If your gate operator predates the current standard or its photocells are knocked out of alignment, your gate can exert real closing force on a person, animal, or vehicle. We check entrapment protection on every automatic gate repair. On Crestline properties where plowed snowbanks knock photocells out of line, we remount sensors above the drift line so they stay aligned through winter.
Because of the mountain climate. Dry summer heat at 4,500 feet shrinks and warps wood panels, while winter snow and wet storms swell the boards and catch the gate bottom, pulling the swing arc out of square. A gate that’s fine in October can be dragging by January and binding by July. Seasonal adjustment, hinge tightening, and realignment keep older wood gates working without forcing the operator to fight the gate. Call (855) 942-4867 and we’ll do a seasonal check.
No, not typically. Standard residential operators are built for flat lots with short, level gate panels. Crestline driveways are sloped, often on dirt or gravel, and the gate catches snow, slush, and runoff all winter. That extra load burns through motors and strips gears quickly. We recommend operators rated for the gate weight and the slope, with proper photocell placement above the snow line. If yours has failed, we’ll size the replacement honestly rather than selling you another unit that won’t last the winter.
Contact Riverside Gate Company for Gate Repair in Crestline
If your gate is dragging, binding, or dead, call (855) 942-4867. We’ll ask a few questions about the gate, the operator brand, and when the problem started, then schedule a Crestline visit. Estimates are free, every price is quoted and agreed before any work starts, and we come prepared with parts for the brands we service. Whether it’s a heaved post above Lake Gregory, a dead control board on an older LiftMaster, or a gate that needs replacing entirely, Riverside Gate Company handles it from the first call to the final swing test.
Written by Neil Dravecky, Owner at Riverside Gate Company, serving Crestline and the San Bernardino Mountains.