Gate Repair in Highland — Same-Day Repair, Priced Before We Start

Fast, Reliable Gate Repair Across Highland

A gate that won’t open or won’t stay closed is a problem you feel every time you leave the house. In Highland, gate repair usually means one of three things: a hinge post that has heaved out of level in the expansive clay, an operator or control board that has failed electrically, or a welded steel or wrought-iron panel that has sagged past the point of adjustment. We fix all three. Riverside Gate Company is a gate-exclusive specialist, not a general contractor that sometimes touches a gate. We service every gate automation brand you’re likely to have on a Highland property, and we carry the parts to do it. If your gate is dragging, faulting, or dead at the keypad, call (855) 942-4867 for a free estimate. We know this area’s gates better than anyone.

Call (855) 942-4867

Why Riverside Gate Company Is Highland’s Preferred Gate Repair Company

Most of the gates we repair in Highland have been standing for 30, 40, sometimes 60 years. That means the original installation was done long before anyone understood how badly the ground moves here. We have repaired gates off Baseline, in the tracts east of Victoria, and up against the foothill edges where the adobe runs deepest. Homeowners in Highland call us because we diagnose the footing, the hinge geometry, and the operator as one system. We don’t just slap a new hinge on a post that’s already tipping out of plumb.

Neil Dravecky built Riverside Gate Company around a simple point: gates are their own trade. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That range matters more in Highland than in most cities, because the housing stock spans 1950s-era tract homes with original iron gates all the way to recent builds with modern slide operators and loop detectors. Whether it’s a residential chain-link gate with a Mighty Mule opener or a commercial slide gate running a DoorKing, the person who shows up has seen that exact setup before.

Wrought Iron Gate Repair in Highland

Wrought iron gate repair in Highland is rarely just about the iron. The work we do most often starts with the post, not the panel. In the older tracts off Baseline, the original gates were hung on shallow concrete footings that never accounted for expansive clay. In summer the ground dries out and the gate swings fine. After winter rains the clay swells, the post heaves, and the gate starts dragging on the driveway or the walk. That is a footing problem. Tightening the hinge does nothing for it, and we tell homeowners that before they spend money on hardware.

Post Reset and Sag Correction

When a wrought-iron gate drags, we measure the post plumb and the panel level first. If the post has moved, the fix is to dig out the old footing, set the post deeper with proper concrete, and then rehang the gate at the correct pitch. We have done this on gates throughout the 92346 zip code, including several where the original footing had cracked clean through.

Hinge and Latch Rebuilds

Highland’s dry heat bakes the grease out of hinges, and Santa Ana winds hammer the panel against the latch. The result is a gate that rattles, binds, or won’t catch when it closes. We rebuild hinge barrels, replace worn pins, and re-align latches so the gate actually closes flush against the block wall. On older wrought iron, we also weld reinforcement gussets where cracks have started at the hinge line.

Typical wrought iron gate repair in Highland runs $185 – $450, depending on whether it is a hinge rebuild, a post reset, or both. A full post reset with new concrete on a large driveway gate can run $600 – $900. We quote the job before any work starts, and the price is the price.

Metal Gate Repair in Highland

Metal gate repair in Highland covers the full range of steel, chain-link, and aluminum gates you see on tract-home driveways and RV access points. The most common failure is hinge sag on gates that have been hanging for decades on posts set in crumbling concrete. But we also see a lot of rust at the bottom rail, where sprinkler overspray and winter rain keep the metal wet against the soil. On a chain-link gate, the tension bar pulls out of the mesh or the post cap rusts through. On a steel tube gate, the weld at the latch side is usually the first thing to crack.

Realignment and Welding

A metal gate that scrapes or won’t latch usually needs realignment before it needs new parts. We cut and re-weld hinges, straighten the panel, and re-set the post if it has shifted. This is dirty, heavy work, and it is exactly what a general handyman service will misdiagnose. We know the difference between a hinge that is worn and a post that is moving in the clay.

Post Rot and Replacement

On older Highland properties, the original posts were often thin-wall steel or uncoated iron set directly in concrete with no drainage. After 40 years, the metal rots at the concrete line and the gate starts leaning. We cut the old post at the base, core out the footing if it’s still sound, and set a new post in properly mixed concrete. In most cases the panel itself is still worth saving.

Metal gate repair in Highland typically runs $160 – $420 for hinge and weld work. A post replacement with concrete runs $350 – $700. Free estimates include a written scope, and we agree on the final number before we start.

Trusted Brands We Service in Highland

We work on the brand you have. That means BFT and FAAC slide operators on Highland commercial properties, Viking and Linear on apartment and HOA gates, and Ghost Controls or Mighty Mule on residential driveway swing gates. Because we service all nine of these brands from one truck, we don’t tell you to call someone else because we don’t handle your equipment. We stock common control boards, safety photocells, remotes, and batteries for the operators we fix most often in Highland. If your gate opener is old enough to predate modern safety requirements, we’ll wire in photo eyes and contact edges that meet current UL 325 standards, even if the original builder never did.

Common Gate Repair Problems We See in Highland Homes

• Seasonal gate swing from expansive clay: The gate clears the driveway in July and grinds on the concrete in February. This is a heaving hinge post, not a hinge problem, and the fix is a deeper footing sized for Highland’s adobe soil.
• Hinge sag on 1950s – 1980s tract gates: Decades of sun, wind, and opening cycles wear hinge barrels and stretch the mount holes. Older gates on East Highland’s block-wall lots are especially prone because the original hinges were never rated for the gate’s full weight.
• Obsolete control boards and dead safety sensors: Automatic gates built before UL 325 standards often lack entrapment protection. We replace old boards with current units and add photocells and contact edges where the original install had none.
• Wind and heat damage on exposed metal: Santa Ana winds work latches loose and bend gate frames, while 100-degree summers accelerate rust and paint failure. Gates facing the foothill canyons get hit hardest because the wind funnels through.

Pricing for Gate Repair in Highland, CA

We Also Serve Cities Near Highland

Riverside Gate Company serves Highland and the surrounding Inland Empire communities, including San Bernardino, Muscoy, Redlands, and Loma Linda. If you’re a property manager or landlord with gates in more than one of those cities, our Gate Repair team handles all of them from one call. And for full details on our Highland coverage area, see Gate Repair in Highland.

FAQs About Gate Repair in Highland